qmk

QMK Firmware
git clone git://git.z3bra.org/qmk.git
Log | Files | Refs | Submodules | LICENSE

rules.mk (3105B)


      1 SRC += i2c.c
      2 SRC += serial.c
      3 SRC += ssd1306.c
      4 
      5 # if firmware size over limit, try this option
      6 # CFLAGS += -flto
      7 
      8 # MCU name
      9 MCU = atmega32u4
     10 
     11 # Processor frequency.
     12 #     This will define a symbol, F_CPU, in all source code files equal to the
     13 #     processor frequency in Hz. You can then use this symbol in your source code to
     14 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
     15 #     automatically to create a 32-bit value in your source code.
     16 #
     17 #     This will be an integer division of F_USB below, as it is sourced by
     18 #     F_USB after it has run through any CPU prescalers. Note that this value
     19 #     does not *change* the processor frequency - it should merely be updated to
     20 #     reflect the processor speed set externally so that the code can use accurate
     21 #     software delays.
     22 F_CPU = 16000000
     23 
     24 #
     25 # LUFA specific
     26 #
     27 # Target architecture (see library "Board Types" documentation).
     28 ARCH = AVR8
     29 
     30 # Input clock frequency.
     31 #     This will define a symbol, F_USB, in all source code files equal to the
     32 #     input clock frequency (before any prescaling is performed) in Hz. This value may
     33 #     differ from F_CPU if prescaling is used on the latter, and is required as the
     34 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
     35 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
     36 #     at the end, this will be done automatically to create a 32-bit value in your
     37 #     source code.
     38 #
     39 #     If no clock division is performed on the input clock inside the AVR (via the
     40 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
     41 F_USB = $(F_CPU)
     42 
     43 # Bootloader selection
     44 #   Teensy       halfkay
     45 #   Pro Micro    caterina
     46 #   Atmel DFU    atmel-dfu
     47 #   LUFA DFU     lufa-dfu
     48 #   QMK DFU      qmk-dfu
     49 #   atmega32a    bootloadHID
     50 BOOTLOADER = caterina
     51 
     52 # Interrupt driven control endpoint task(+60)
     53 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
     54 
     55 # Build Options
     56 #   change to "no" to disable the options, or define them in the Makefile in
     57 #   the appropriate keymap folder that will get included automatically
     58 #
     59 BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
     60 MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
     61 EXTRAKEY_ENABLE = no       # Audio control and System control(+450)
     62 CONSOLE_ENABLE = no         # Console for debug(+400)
     63 COMMAND_ENABLE = no        # Commands for debug and configuration
     64 NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
     65 BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
     66 MIDI_ENABLE = no            # MIDI controls
     67 AUDIO_ENABLE = no           # Audio output on port C6
     68 UNICODE_ENABLE = no         # Unicode
     69 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
     70 RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.
     71 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
     72 SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
     73 
     74 CUSTOM_MATRIX = yes
     75 
     76 DEFAULT_FOLDER = lily58/rev1