qmk

QMK Firmware
git clone git://git.z3bra.org/qmk.git
Log | Files | Refs | Submodules | LICENSE

rules.mk (2837B)


      1 # MCU name
      2 MCU = atmega32u4
      3 
      4 # Processor frequency.
      5 #     This will define a symbol, F_CPU, in all source code files equal to the
      6 #     processor frequency in Hz. You can then use this symbol in your source code to
      7 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
      8 #     automatically to create a 32-bit value in your source code.
      9 #
     10 #     This will be an integer division of F_USB below, as it is sourced by
     11 #     F_USB after it has run through any CPU prescalers. Note that this value
     12 #     does not *change* the processor frequency - it should merely be updated to
     13 #     reflect the processor speed set externally so that the code can use accurate
     14 #     software delays.
     15 F_CPU = 16000000
     16 
     17 #
     18 # LUFA specific
     19 #
     20 # Target architecture (see library "Board Types" documentation).
     21 ARCH = AVR8
     22 
     23 # Input clock frequency.
     24 #     This will define a symbol, F_USB, in all source code files equal to the
     25 #     input clock frequency (before any prescaling is performed) in Hz. This value may
     26 #     differ from F_CPU if prescaling is used on the latter, and is required as the
     27 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
     28 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
     29 #     at the end, this will be done automatically to create a 32-bit value in your
     30 #     source code.
     31 #
     32 #     If no clock division is performed on the input clock inside the AVR (via the
     33 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
     34 F_USB = $(F_CPU)
     35 
     36 # Interrupt driven control endpoint task(+60)
     37 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
     38 
     39 
     40 # Bootloader selection
     41 #   Teensy       halfkay
     42 #   Pro Micro    caterina
     43 #   Atmel DFU    atmel-dfu
     44 #   LUFA DFU     lufa-dfu
     45 #   QMK DFU      qmk-dfu
     46 #   atmega32a    bootloadHID
     47 BOOTLOADER = caterina
     48 
     49 
     50 # If you don't know the bootloader type, then you can specify the
     51 # Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
     52 #   Teensy halfKay      512
     53 #   Teensy++ halfKay    1024
     54 #   Atmel DFU loader    4096
     55 #   LUFA bootloader     4096
     56 #   USBaspLoader        2048
     57 # OPT_DEFS += -DBOOTLOADER_SIZE=4096
     58 
     59 
     60 # Build Options
     61 #   comment out to disable the options.
     62 #
     63 BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
     64 MOUSEKEY_ENABLE = yes	  # Mouse keys(+4700)
     65 EXTRAKEY_ENABLE = yes	  # Audio control and System control(+450)
     66 CONSOLE_ENABLE = no			# Console for debug(+400)
     67 COMMAND_ENABLE = no     # Commands for debug and configuration
     68 SLEEP_LED_ENABLE = no   # Breathing sleep LED during USB suspend
     69 NKRO_ENABLE = yes				# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
     70 BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
     71 AUDIO_ENABLE = no
     72 RGBLIGHT_ENABLE = yes
     73 
     74 LAYOUTS = 60_ansi